MC9S08SH16MTJR

MC9S08SH16MTJR图片1
MC9S08SH16MTJR图片2
MC9S08SH16MTJR图片3
MC9S08SH16MTJR概述

其他系列 40MHz 闪存:16K@x8bit RAM:1KB

Overview

The S08SH family is a series of S08 8-bit microcontrollers that offer a new low-end option for applications in the 5-volt range. The S08SH family is pin, tool and software compatible with S08SG, offering greater design flexibility. It also has wide peripheral offering with serial communications interface SCI, serial peripheral interface SPI, I²C, analog-to-digital converter ADC, analog comparator and temperature sensor.

Product comparison table

MoreLess

## Features

### 8-bit HCS08 Central Processor Unit CPU

* Up to 40 MHz HCS08 CPU 20 MHz bus frequency for 50 ns minimum instruction time

* HC08 instruction set with added BGND instruction

* Support for up to 32 interrupt/reset sources

### Integrated Third-Generation Flash Memory and RAM

* Embedded flash that is in-application reprogrammable

* Extremely fast, byte-writable programming, as fast as 20 µs/byte

* Up to 100,000 write/erase cycles at typical voltage and temperature 10k minimum write/erase

* 100 years typical data retention 15 years minimum

### Flexible Clock Options

* Internal clock source ICS module containing a frequencylocked loop FLL controlled by internal or external reference

* Precision trimming of internal reference allows typical 0.1 percent resolution and +0.5 percent to -1 percent deviation over operating temperature and voltage

* Internal reference can be trimmed from 31.25 kHz to 39.065 kHz, allowing for 16 MHz to 20 MHz FLL output

* Low-power oscillator module XOSC

* software selectable crystal or ceramic resonator range, 31.25 kHz to 38.4 kHz or 1 MHz to 16 MHz,

* supports external clock source input up to 40 MHz

### Input/Output

* Up to 23 bidirectional lines

* One Output-Only Line

* Outputs 10 mA each; 60 mA max for package

* Software selectable pull-ups on ports when used as input

* internal pull-up on reset and interrupt request IRQ pin

* Software selectable slew rate control and drive strength on ports when used as output

* 8-pin keyboard interrupt module with software selectable polarity on edge or edge/level modes

### Ganged Output Option for PTB 5:2 and PTC 3:0

* Allows single write to change state of multiple pins

* Drives up to 80 mA without risk of runaway code shorting

* Provides option to tie multiple pins from different ports to same control registers

* Safely drives multiple outputs

### Multiple Serial Communication Options

* Serial communications interface module with option for 13-bit break capabilities and double-buffered transmit and receive

* Serial peripheral interface module and I2C bus module

### Integrated Analog Peripherals

* 16-ch., 10-bit analog-to-digital converter ADC

* Automatic compare function, software programmable for greater than/equal to or less than conditions

* Asynchronous clock source

* Temperature sensor

* Internal bandgap reference channel

* Hardware triggerable using the RTI counter

* Low-power and high-speed options

* Analog comparator module ACMP

* Option to compare to internal reference

* Option to route comparator output directly to pin

* Output can be optionally routed to TPM module as input capture trigger

* Real-time-counter RTC

* 8-bit modulus counter with binary or decimal based prescaler

* External clock source for prescise time base, time-of-day, calendar or task scheduling functions

### Three Timer Modules

* Programmable 16-bit timer/PWM modules TPM1 and TPM2

* 8-bit modulo timer module MTIM with 8-bit prescaler

### System Protection

* Watchdog computer operating properly COP reset with option to run from dedicated 1 kHz internal clock source or bus clock

* Low-voltage detection with reset or interrupt

* Illegal opcode detection with reset

* Flexible block protection

* Security feature for flash and RAM

* Always-on power-on reset POR circuitry

### Development Support

* Background Debugging System

* On-Chip In-Circuit Emulation ICE

* Real-Time Bus CaptureComparison Table

### S08SH Family Members

| ADC Channels

S08QG| | | | | |

S08SH32| | | | | |

RS08KA| | | | | |

S08QD| | | | | |

S08SG| | | | | |

°GPIO count does not include the output-only PTA4/ACMPO/BKGD/MS. °8-Pin package does not contains XOSC, SPI, SCI and has 1 channel by timer module

MC9S08SH16MTJR中文资料参数规格
技术参数

无卤素状态 Halogen Free

RAM大小 1 KB

FLASH内存容量 16 kB

模数转换数ADC 1

工作温度Max 125 ℃

工作温度Min -40 ℃

电源电压Max 5.5 V

电源电压Min 2.7 V

封装参数

安装方式 Surface Mount

引脚数 20

封装 SOP-20

外形尺寸

封装 SOP-20

物理参数

重量 81.4 mg

其他

产品生命周期 Active

包装方式 Tape & Reel TR

符合标准

RoHS标准 RoHS Compliant

含铅标准 Lead Free

数据手册

在线购买MC9S08SH16MTJR
型号: MC9S08SH16MTJR
制造商: NXP 恩智浦
描述:其他系列 40MHz 闪存:16K@x8bit RAM:1KB

锐单商城 - 一站式电子元器件采购平台