PCAL9539AHF,128

NXP  PCAL9539AHF,128  输入/输出扩展, 16bit, 400 kHz, I2C, 1.65 V, 5.5 V, HWQFN

Overview

The PCAL9539A is a low-voltage 16-bit General Purpose Input/Output GPIO expander with interrupt and reset for I²C-bus/SMBus applications. I/O expanders provide a simple solution when additional I/Os are needed while keeping interconnections to a minimum, for example, in ACPI power switches, sensors, push buttons, LEDs, fan control, etc.

In addition to providing a flexible set of GPIOs, the wide VDD range of 1.65 V to 5.5 V allows the PCAL9539A to interface with next-generation microprocessors and microcontrollers where supply levels are dropping down to conserve power.

The PCAL9539A contains the PCA9539 register set of four pairs of 8-bit Configuration, Input, Output, and Polarity Inversion registers, and additionally, the PCAL9539A has Agile I/O, which are additional features specifically designed to enhance the I/O. These additional features are: programmable output drive strength, latchable inputs, programmable pull-up/pull-down resistors, maskable interrupt, interrupt status register, programmable open-drain or push-pull outputs.

The PCAL9539A is a pin-to-pin replacement to the PCA9539 and PCA9539A, however, the PCAL9539A powers up with all I/O interrupts masked. This mask default allows for a board bring-up free of spurious interrupts at power-up.

The PCAL9539A open-drain interrupt INT output is activated when any input state differs from its corresponding Input Port register state and is used to indicate to the system master that an input state has changed.

INT can be connected to the interrupt input of a microcontroller. By sending an interrupt signal on this line, the remote I/O can inform the microcontroller if there is incoming data on its ports without having to communicate via the I²C-bus. Thus, the PCAL9539A can remain a simple slave device.

The device outputs have 25 mA sink capabilities for directly driving LEDs while consuming low device current.

The power-on reset sets the registers to their default values and initializes the device state machine. In the PCAL9539A, the RESET pin causes the same reset/default I/O input configuration to occur without de-powering the device, holding the registers and I²C-bus state machine in their default state until the RESET input is once again HIGH. This input requires a pull-up to VDD.

Two hardware pins A0, A1 select the fixed I2C-bus address and allow up to four devices to share the same I²C-bus/SMBus.

MoreLess

## Features

* I²C-bus to parallel port expander

* Operating power supply voltage range of 1.65 V to 5.5 V

* Low standby current consumption:

* 1.5 μA typical at 5 V VDD

* 1.0 μA typical at 3.3 V VDD

* Schmitt-trigger action allows slow input transition and better switching noise immunity at the SCL and SDA inputs

* Vhys = 0.10 x VDD typical

* 5 V tolerant I/Os

* Active LOW reset input RESET

* Open-drain active LOW interrupt output INT

* 400 kHz Fast-mode I²C-bus

* Internal power-on reset

* Power-up with all channels configured as inputs

* No glitch on power-up

* Latched outputs with 25 mA drive maximum capability for directly driving LEDs

* Latch-up performance exceeds 100 mA per JESD78, Class II

* ESD protection exceeds JESD22:

* 2000 V Human Body Model A114-A

* 1000 V Charged-Device Model C101

* Packages offered: TSSOP24, HVQFN24

### Agile I/O features

* Pin to pin replacement for PCA9539 and PCA9539A with interrupts disabled at power-up

* Software backward compatible with PCA9539 and PCA9539A

* Output port configuration: bank selectable push-pull or open-drain output stages

* Interrupt status: read-only register identifies the source of an interrupt

* Bit-wise I/O programming features:

* Output drive strength: four programmable drive strengths to reduce rise and fall times in low capacitance applications

* Input latch: Input Port register values changes are kept until the Input Port register is read

* Pull-up/pull-down enable: floating input or pull-up/down resistor enable

* Pull-up/pull-down selection: 100 kΩ pull-up/down resistor selection

* Interrupt mask: mask prevents the generation of the interrupt when input changes state

## Features