PIC18LF458-I/L

PIC18LF458-I/L图片1
PIC18LF458-I/L图片2
PIC18LF458-I/L图片3
PIC18LF458-I/L图片4
PIC18LF458-I/L图片5
PIC18LF458-I/L图片6
PIC18LF458-I/L图片7
PIC18LF458-I/L图片8
PIC18LF458-I/L图片9
PIC18LF458-I/L图片10
PIC18LF458-I/L图片11
PIC18LF458-I/L图片12
PIC18LF458-I/L图片13
PIC18LF458-I/L概述

MICROCHIP  PIC18LF458-I/L  微控制器, 8位, 闪存, PIC18LF, 40 MHz, 32 KB, 1.5 KB, 44 引脚, LCC

DEVICE OVERVIEW

This document contains device specific information for the following devices:

• PIC18F248

• PIC18F258

• PIC18F448

• PIC18F458

These devices are available in 28-pin, 40-pin and 44-pin packages. They are differentiated from each other in four ways:

1\. PIC18FX58 devices have twice the Flash program memory and data RAM of PIC18FX48 devices 32 Kbytes and 1536 bytes vs. 16 Kbytes and 768 bytes, respectively.

2\. PIC18F2X8 devices implement 5 A/D channels, as opposed to 8 for PIC18F4X8 devices.

3\. PIC18F2X8 devices implement 3 I/O ports, while PIC18F4X8 devices implement 5.

4\. Only PIC18F4X8 devices implement the Enhanced CCP module, analog comparators and the  Parallel Slave Port.

All other features for devices in the PIC18FXX8 family, including the serial communications modules, are identical. These are summarized in Table 1-1. Block diagrams of the PIC18F2X8 and PIC18F4X8 devices are provided in Figure 1-1 and Figure 1-2, respectively. The pinouts for these device families are listed in Table 1-2.

High-Performance RISC CPU:

• Linear program memory addressing up to 2 Mbytes

• Linear data memory addressing to 4 Kbytes

• Up to 10 MIPS operation

• DC – 40 MHz clock input

• 4 MHz-10 MHz oscillator/clock input with PLL active

• 16-bit wide instructions, 8-bit wide data path

• Priority levels for interrupts

• 8 x 8 Single-Cycle Hardware Multiplier

Peripheral Features:

• High current sink/source 25 mA/25 mA

• Three external interrupt pins

• Timer0 module: 8-bit/16-bit timer/counter with 8-bit programmable prescaler

• Timer1 module: 16-bit timer/counter

• Timer2 module: 8-bit timer/counter with 8-bit period register time base for PWM

• Timer3 module: 16-bit timer/counter

• Secondary oscillator clock option – Timer1/Timer3

• Capture/Compare/PWM CCP modules; CCP pins can be configured as:

\- Capture input: 16-bit, max resolution 6.25 ns

\- Compare: 16-bit, max resolution 100 ns TCY

\- PWM output: PWM resolution is 1 to 10-bit

  Max. PWM freq. @:8-bit resolution = 156 kHz

                   10-bit resolution = 39 kHz

• Enhanced CCP module which has all the features of the standard CCP module, but also has the following features for advanced motor control:

\- 1, 2 or 4 PWM outputs

\- Selectable PWM polarity

\- Programmable PWM dead time

• Master Synchronous Serial Port MSSP with two modes of operation:

\- 3-wire SPI™ Supports all 4 SPI modes

\- I2C™ Master and Slave mode

• Addressable USART module:

\- Supports interrupt-on-address bit

Advanced Analog Features:

• 10-bit, up to 8-channel Analog-to-Digital Converter module A/D with:

\- Conversion available during Sleep

\- Up to 8 channels available

• Analog Comparator module:

\- Programmable input and output multiplexing

• Comparator Voltage Reference module

• Programmable Low-Voltage Detection LVD module:

\- Supports interrupt-on-Low-Voltage Detection

• Programmable Brown-out Reset BOR CAN bus Module Features:

• Complies with ISO CAN Conformance Test

• Message bit rates up to 1 Mbps

• Conforms to CAN 2.0B Active Spec with:

\- 29-bit Identifier Fields

\- 8-byte message length

\- 3 Transmit Message Buffers with prioritization

\- 2 Receive Message Buffers

\- 6 full, 29-bit Acceptance Filters

\- Prioritization of Acceptance Filters

\- Multiple Receive Buffers for High Priority

  Messages to prevent loss due to overflow

\- Advanced Error Management Features

Special Microcontroller Features:

• Power-on Reset POR, Power-up Timer PWRT and Oscillator Start-up Timer OST

• Watchdog Timer WDT with its own on-chip RC oscillator

• Programmable code protection

• Power-saving Sleep mode

• Selectable oscillator options, including:

\- 4x Phase Lock Loop PLL of primary oscillator

\- Secondary Oscillator 32 kHz clock input

• In-Circuit Serial ProgrammingTM ICSPTM via two pins

Flash Technology:

• Low-power, high-speed Enhanced Flash technology

• Fully static design

• Wide operating voltage range 2.0V to 5.5V

• Industrial and Extended temperature ranges

PIC18LF458-I/L中文资料参数规格
技术参数

电源电压DC 5.00 V, 5.50 V max

针脚数 44

时钟频率 40.0 MHz

RAM大小 1.5 KB

位数 8

耗散功率 1000 mW

FLASH内存容量 32 KB

I/O引脚数 33

存取时间 40.0 µs

内核架构 PIC

内存容量 32000 B

内核子架构 PIC18

输入/输出数 33 Input

工作温度Max 85 ℃

工作温度Min -40 ℃

耗散功率Max 1000 mW

电源电压 2V ~ 5.5V

电源电压Max 5.5 V

电源电压Min 2 V

封装参数

安装方式 Surface Mount

引脚数 44

封装 PLCC-44

外形尺寸

长度 16.59 mm

宽度 16.59 mm

高度 3.87 mm

封装 PLCC-44

物理参数

工作温度 -40℃ ~ 85℃

其他

产品生命周期 Unknown

包装方式 Tube

符合标准

RoHS标准 RoHS Compliant

含铅标准 Lead Free

REACH SVHC标准 No SVHC

REACH SVHC版本 2015/12/17

海关信息

ECCN代码 3A991.a.2

数据手册

PIC18LF458-I/L引脚图与封装图
PIC18LF458-I/L引脚图
PIC18LF458-I/L封装图
PIC18LF458-I/L封装焊盘图
在线购买PIC18LF458-I/L
型号: PIC18LF458-I/L
制造商: Microchip 微芯
描述:MICROCHIP  PIC18LF458-I/L  微控制器, 8位, 闪存, PIC18LF, 40 MHz, 32 KB, 1.5 KB, 44 引脚, LCC
替代型号PIC18LF458-I/L
型号/品牌 代替类型 替代型号对比

PIC18LF458-I/L

Microchip 微芯

当前型号

当前型号

PIC18F458-I/L

微芯

类似代替

PIC18LF458-I/L和PIC18F458-I/L的区别

PIC18LF4431-I/PT

微芯

类似代替

PIC18LF458-I/L和PIC18LF4431-I/PT的区别

PIC18LF458T-I/L

微芯

类似代替

PIC18LF458-I/L和PIC18LF458T-I/L的区别

锐单商城 - 一站式电子元器件采购平台