UJA1075ATW/5V0/WD

CAN 20Kbps Normal/Standby Automotive 32Pin HTSSOP EP Tube

General description

The UJA1075A core System Basis Chip SBC replaces the basic discrete components commonly found in Electronic Control Units ECU with a high-speed Controller Area Network CAN and a Local Interconnect Network LIN interface.

The UJA1075A supports the networking applications used to control power and sensor peripherals by using a high-speed CAN as the main network interface and the LIN interface as a local sub-bus.

General description

The UJA1075 core System Basis Chip SBC replaces the basic discrete components commonly found in Electronic Control Units ECU with a high-speed Controller Area Network CAN and a Local Interconnect Network LIN interface.

The UJA1075 supports the networking applications used to control power and sensor peripherals by using a high-speed CAN as the main network interface and the LIN interface as a local sub-bus.

Features and benefits

General

Contains a full set of CAN and LIN ECU functions:

  ‹CAN transceiver and LIN transceiver

‹  Scalable 3.3 V or 5 V voltage regulator delivering up to 250 mA for a microcontroller and peripheral circuitry; an external PNP transistor can be connected for better heat distribution over the PCB

  ‹Separate voltage regulator for the CAN transceiver 5 V

  ‹Watchdog with Window and Timeoutmodes and on-chip oscillator

  ‹Serial Peripheral Interface SPI for communicating with the microcontroller

‹  ECU power management system

Designed for automotive applications:

  ‹Excellent ElectroMagnetic Compatibility EMC performance

  ‹±8 kV ElectroStatic Discharge ESD protection Human Body Model HBM on the CAN/LIN bus pins and the wake pins

  ‹±6 kV ElectroStatic Discharge ESD protection IEC 61000-4-2 on the CAN/LIN bus pins and the wake pins

  ‹±58 V short-circuit proof CAN/LIN bus pins

  ‹Battery and CAN/LIN bus pins are protected against transients in accordance with ISO 7637-3

Supports remote flash programming via the CAN bus

Small 6.1 mm ×11 mm HTSSOP32 package with low thermal resistance

Pb-free; RoHS and dark green compliant

CAN transceiver

ISO 11898-2 and ISO 11898-5 compliant high-speed CAN transceiver

Dedicated low dropout voltageregulator for the CAN bus:

  ‹Independent of the microcontroller supply

  ‹Significantly improves EMC performance

Bus connections are truly floating when power is off

SPLIT output pin for stabilizing the recessive bus level

LIN transceiver

LIN 2.1 compliant LIN transceiver

Compliant with SAE J2602

Downward compatible with LIN 2.0 and LIN 1.3

Low slope mode for optimized EMC performance

Integrated LIN termination diode at pin DLIN

Power management

Wake-up via CAN, LIN or local wake pins with wake-up source detection

2 Wake pins:

  ‹WAKE1 and WAKE2 inputs can be switched off to reduce current flow

  ‹Output signal WBIAS to bias the wake pins, selectable sampling time of 16 ms or 64 ms

Standby mode with very low standby current and full wake-up capability; V1 active to maintain supply to the microcontroller

Sleep mode with very low sleep current and full wake-up capability

Control and Diagnostic features

Safe and predictable behavior under all conditions

Programmable watchdog with independent clock source:

  ‹Window, Timeout with optional cyclic wake-up and Off modes supported with automatic re-enable in the event of an interrupt

16-bit Serial Peripheral Interface SPI for configuration, control and diagnosis

Global enable output for controlling safety-critical hardware

Limp home output LIMP for activating application-specific ‘limp home’ hardware in the event of a serious system malfunction

Overtemperature shutdown

Interrupt output pin; interrupts can be individually configured to signal V1/V2 undervoltage, CAN/LIN/local wake-up and cyclic and power-on interrupt events

Bidirectional reset pin with variable power-on reset length to support a variety of microcontrollers

Software-initiated system reset