| |
### Contactor, 100 Amps, SPDT, 500 MS Time Delay, To MIL-PRF-6106
---
|
---
|
###---
Designed to meet the requirements of MIL-PRF-6106
**Contact Arrangement:** SPDT 1 Form C
**Weight: ** 18 oz approx.
###
**Contact Rating: **
For other main contact or auxiliary contact ratings consult the factory
**Power Contacts:**
**Resistive: **100 Amps @ 28 VDC or 115/208V 400 Hz
**Inductive:**
100 Amps @ 115/208V 400 Hz
50 Amps @ 28 VDC
**Motor:**
50 Amps @ 28 VDC or 115/208V 400 Hz
**Lamp:**
20 Amps @ 28 VDC or 115/208V 400 Hz
**Auxiliary Contacts: **
**Configuration ** SPDT
**Current Rating ** 5 Amps @ 28 VDC
**Life: **
50,000 cycles @ rated loads
25,000 cycles Lamp load life
10,000 cycles Transfer load
100,000 cycles Mechanical
**Rupture: ** 1000 Amperes **
main contacts**Overload: ** 800 Amperes
main contacts
**Operate Time: ** 500 ms min
**Release Time: ** 50 ms max
**Contact Bounce Time: ** 3 ms max @ rated contact load, 28 VDC
**Coil Data:**
@ 28 VAC and 25°C
**Nominal Coil Voltage: ** 28 to 30 VDC
**Pull-In Voltage: ** 20 VDC max @ 85°C
**Drop-out Voltage: ** 1.5 to 7.0 VDC
**Coil Resistance: ** 152 Ohms
###
**Temperature Range:** -55°C to +85°C
**Altitude: ** 50,000 ft
**Vibration:**
For applications requiring other vibration levels, consult the factory.
**10 G"s 50-500 Hz
5 G"s 500-2000 Hz**Shock Operating: ** 25 G"s 6 ms
For applications requiring other shock levels, consult the factory.
**Acceleration: ** 15 G"s
###
**Duty Cycle: ** Continuous
**Insulation Resistance: ** 100 megohms @ 500V 25°C
**Dielectric Strength: **
**Sea Level: **
**Contact to Case **1,250 VRMS
**Contact to Coil **1,250 VRMS
**Coil to Case** 1,250 VRMS
**Across Open Contacts ** 1,250 VRMS
**50,000 Feet:
All points1\. For other main contact or auxiliary contact ratings consult the factory.
2\. For applications requiring higher shock and vibration, consult the factory.
---
The Contactor is designed to meet the general requirements of MIL-PRF-6106. Solid state control and logic is protected against inadvertent operation from noise, transients, or RFI/EMI and all solid state components are JANTX rated or better. This power contactor features a gasket sealed, vented, construction with a light weight aluminum housing. The power terminals are Silver plated Beryllium copper to prevent any possibility of corrosion during use. All auxiliary switches are QPL listed MS-24547 types.
**Overall Dimensions
** Numbers for reference only.
|
| |
**Schematic**
---
| | |
**Contactor General Notes**
• Unless otherwise specified, all tests made at nominal coil voltages, @ 25ºC.
---
• For special coil variations, switching configurations, terminals styles, mounting types, time delays, or other control circuits consult the factory.
• Unless otherwise specified, tolerances on decimal dimensions are ± .010"".
• Specifications contained herein are subject to change without notice.