ADUCRF101BCPZ128

射频微控制器 - MCU Cortex M 3 MCU + RF integration I.C

Product Details

The ADuCRF101 is a fully integrated, data acquisition solution that is designed for low power, wireless applications. It features a 12-bit analog-to-digital converter ADC, a low power ARM Cortex™-M3 processor, a 862 MHz to 928 MHz and 431 MHz to 464 MHz RF transceiver, and Flash®/EE memory. The ADuCRF101 is packaged in a 9 mm × 9 mm LFCSP.

The data acquisition section consists of a 12-bit SAR ADC. The six inputs can be configured in single-ended or differential mode. When configured in single-ended mode, they can be used for ratiometric measurements on sensors that are powered, when required, from the internal low dropout regulator LDO. An internal battery monitor channel and an on-chip tempera-ture sensor are also available.

This wireless data acquisition system is designed to operate in battery-powered applications where low power is critical. The device can be configured in normal operating mode or different low power modes under direct program control. In flexi mode, any peripheral can wake up the device and operate it. In hibernate mode, the internal wake-up timer remains active. In shutdown mode, only an external interrupt can wake up the device.

The ADuCRF101 integrates a low power ARM Cortex-M3 processor. It is a 32-bit RISC machine, offering up to 1.25 DMIPS peak performance. The ARM Cortex-M3 processor also has a flexible 14-channel direct memory access DMA controller that supports communication peripherals, serial peripheral interface SPI, UART, and I2C. Also provided on chip are 128 kB of nonvolatile Flash/EE memory and 16 kB of SRAM.

A 16 MHz on-chip oscillator generates the system clock. This clock can be internally divided for the processor to operate at a lower frequency, thus saving power. A low power, internal 32 kHz oscillator is available and can be used to clock the four timers, as follows: two general-purpose timers, a wake-up timer, and a system watchdog timer.

A range of communication peripherals can be configured, as required, in a specific application. These peripherals include UART, I2C, SPI, GPIO ports, PWM, and RF transceivers.

The RF transceiver communicates in the 862 MHz to 928 MHz and 431 MHz to 464 MHz frequency bands using multiple configurations.

On-chip factory firmware supports in-circuit serial download via the UART, and nonintrusive emulation and program download are also supported via the serial wire interface. These features are incorporated into a low cost development system supporting this precision analog microcontroller family.

The ADuCRF101 operates from 2.2 V to 3.6 V and is specified over an industrial temperature range of −40°C to +85°C. It is available in a 64-lead LFCSP package

**APPLICATIONS**

.

Battery powered wireless sensor

.

Medical telemetry systems

.

Industrial and home automation

.

Asset tracking

.

Security systems access systems

.

Health and fitness applications

### Features and Benefits

.

Analog I/O

.

**6-Channel 12-bit SAR ADC**

Single-ended and differential inputs

Programmable data rate up to 167 kSPS

On-chip voltage reference 

Supply rante: 2.2V to 3.6V

.

**Power Consumption**

280 nA, in power-down mode, nonretained state

1.9 µA, in power-down mode, processor memory and transceiver memory retained

.

210 µA/Mhz, Cortex-M3 in active mode

12.8 mA transceiver in receive mode, Cortex-M3 in power-down mode

9 mA to 32 mA transceiver in transmit mode, Cortex-M3 in power-down mode

.

**RF Transceiver**

Frequency bands, 862 MHz to 928 MHz and 431 MHz to 464 MHz

Multiple Configurations supported

Receiver sensitivity BER, −107.5 dBm at 38.4 kbps, 2FSK

Single and ended and differential PA

Low external BOM

.

**Microcontroller**

32-bit ARM Cortex-M3 processor

Serial Wire download and debug

External Watch crystal for wakeup timer

16 MHz internal Oscillator with 8-way Programmable Divider

.

**Memory** 128 kB Flash/EE memory, 16 kB SRAM

10,000-cycle Flash/EE endurance

10-year Flash/EE retention

In-circuit download via serial wire and UART

.

On-Chip Peripherals

.

**UART, I2C and SPI Serial I/O**

28-pin GPIO port

2 general-purpose, 16-bit timers

32-bit wake-up timer

16-bit watchdog timer

8-channel pulse-width modulation PWM

.

**Package**

64-lead, 9 mm × 9 mm LFCSP

Temperature range: −40°C to +85°C

.

**Tools**

Low cost development system

Third-party compiler and emulator tool support