SC28L91A1B,551

UART 接口集成电路 UART SINGLE W/FIFO

Overview

The SC28L91 is a new member of the IMPACT family of Serial Communications Controllers. It is a single channel UART operating at 3.3 V and 5.0 V VCC, 8 or 16 byte FIFOs and is quite compatible with software of the SC28L92 and previous UARTs offered by Philips. It is a new part that is similar to our previous one channel part but is vastly improved. The improvements being: 16 character receiver, 16 character transmit FIFOs, watch dog timer for the receiver, mode register 0 is added, extended baud rate, over all faster bus and data speeds, programmable receiver and transmitter interrupts and versatile I/O structure. The previous one channel part, SCC2691, is NOT being discontinued.

Pin programming will allow the device to operate with either the Motorola or Intel bus interface. Bit 3 of the MR0 register allows the device to operate in an 8-byte FIFO mode if strict compliance with an 8-byte FIFO structure is required.

The Philips Semiconductors SC28L91 Universal Asynchronous Receiver/Transmitter UART is a single-chip CMOS-LSI communications device that provides a full-duplex asynchronous receiver/transmitter channel in a single package. It interfaces directly with microprocessors and may be used in a polled or interrupt driven system with modem and DMA interface.

The operating mode and data format of the channel can be programmed independently. Additionally, the receiver and transmitter can select its operating speed as one of 28 fixed baud rates; a 16X clock derived from a programmable counter/timer, or an external 1X or 16X clock. The baud rate generator and counter/timer can operate directly from a crystal or from external clock inputs. The ability to independently program the operating speed of the receiver and transmitter make the UART particularly attractive for dual-speed channel applications such as clustered terminal systems.

The receiver and transmitter is buffered by 8 or 16 character FIFOs to minimize the potential of receiver overrun, transmitter underrun and to reduce interrupt overhead in interrupt driven systems. In addition, a flow control capability is provided via RTS/CTS signaling to disable a remote transmitter when the receiver buffer is full.

DMA interface is and other general purpose signals are provided on the SC28L91 via a multipurpose 7-bit input port and a multipurpose 8-bit output port. These can be used as general-purpose ports or can be assigned specific functions such as clock inputs or status/interrupt outputs, FIFO conditions under program control.

The SC28L91 is available in two package versions: a 44-pin PLCC and 44-pin plastic quad flat pack PQFP.

MoreLess

## Features

* Member of IMPACT family: 3.3 to 5.0 volt , -40 Cel to +85 Cel and 68K for 80xxx bus interface for all devices.

* A full-duplex independent asynchronous receiver/transmitter

* 16 character FIFOs for each receiver and transmitter

* Pin programming selects 68K or 80xxx-bus interface

* Programmable data format

* 5 to 8 data bits plus parity

* Odd, even, no parity or force parity

* \\- 1, 1.5 or 2 stop bits programmable in 1/16-bit increments

* 16-bit programmable Counter/Timer

* Programmable baud rate for each receiver and transmitter selectable from:

* 28 fixed rates: 50 to 230.4 k baud

* Other baud rates to 1 MHz at 16X

* Programmable user-defined rates derived from a programmable counter/timer

* External 1X or 16X clock

* Parity, framing, and overrun error detection

* False start bit detection

* Line break detection and generation

* Programmable channel mode

* Normal full-duplex

* Automatic echo

* Local loop back

* Remote loop back

* Multi-drop mode also called "wake-up" or "9-bit"

* Multi-function 7-bit input port includes IACKN

* Can serve as clock or control inputs

* Change of state detection on four inputs

* Inputs have typically >100 kΩ pull-up resistors

* Change of state detectors for modem control

* Multi-function 8-bit output port

* Individual bit set/reset capability

* Outputs can be programmed to be status/interrupt signals

* FIFO status for DMA interface

* Versatile interrupt system

* Single interrupt output with eight maskable interrupting conditions

* Output port can be configured to provide a total of up to six separate interrupt outputs that may be wire ORed.

* Each FIFO can be programmed for four different interrupt levels

* Watchdog timer for the receiver

* Maximum data transfer rates:

* 1X - 1 Mbit/s, 16X - 1 Mbit/s

* Automatic wake-up mode for multi-drop applications

* Start-end break interrupt/status with mid-character break detect.

* On-chip crystal oscillator

* Power-down mode

* Receiver time-out mode

* Single +3.3 V or +5 V power supply

## Features