LPC4370FET100E

LPC4370 系列 204 MHz 282 kB RAM 双核 32 位 微控制器 - TFBGA-100

* Main Cortex-M4 processor: * ARM Cortex-M4 processor, running at frequencies of up to 204 MHz * ARM Cortex-M4 built-in Memory Protection Unit MPU supporting eight regions * ARM Cortex-M4 built-in Nested Vectored Interrupt Controller NVIC * Hardware floating-point unit * Non-maskable Interrupt NMI input * JTAG and Serial Wire Debug SWD, serial trace, eight breakpoints, and four watchpoints * Enhanced Trace Module ETM and Enhanced Trace Buffer ETB support * System tick timer * Cortex-M0 coprocessor: * ARM Cortex-M0 coprocessor capable of off-loading the main ARM Cortex-M4processor * Running at frequencies of up to 204 MHz * JTAG and built-in NVIC * Cortex-M0 subsystem: * ARM Cortex-M0 processor controlling the SPI and SGPIO peripherals residing ona separate AHB multilayer matrix with direct access to 2 kB + 16 kB of SRAM * Running at frequencies of up to 204 MHz * Connected via a core-to-core bridge to the main AHB multilayer matrix and themain ARM Cortex-M4 processor * JTAG and built-in NVIC * On-chip memory: * 264 kB SRAM for code and data use on the main AHB multilayer matrix plus 18 kBof SRAM on the Cortex-M0 subsystem * Multiple SRAM blocks with separate bus access. Two SRAM blocks can bepowered down individually * 64 kB ROM containing boot code and on-chip software drivers * 64-bit + 256 bit general-purpose One-Time Programmable OTP memory * Configurable digital peripherals: * Serial GPIO SGPIO interface * State Configurable Timer SCT subsystem on AHB * Global Input Multiplexer Array GIMA allows to cross-connect multiple inputs andoutputs to event driven peripherals like the timers, SCT, and ADC0/1 * Serial interfaces: * Quad SPI Flash Interface SPIFI with four lanes and up to 52 MB per second * 10/100T Ethernet MAC with RMII and MII interfaces and DMA support for highthroughput at low CPU load. Support for IEEE 1588 time stamping/advanced timestamping IEEE 1588-2008 v2 * One High-speed USB 2.0 Host/Device/OTG interface with DMA support andon-chip high-speed PHY * One High-speed USB 2.0 Host/Device interface with DMA support, on-chipfull-speed PHY and ULPI interface to external high-speed PHY * USB interface electrical test software included in ROM USB stack * One 550 UART with DMA support and full modem interface * Three 550 USARTs with DMA and synchronous mode support and a smart cardinterface conforming to ISO7816 specification. One USART with IrDA interface * Two C_CAN 2.0B controllers with one channel each. Use of C_CAN controllerexcludes operation of all other peripherals connected to the same bus bridge * Two SSP controllers with FIFO and multi-protocol support. Both SSPs with DMAsupport * One SPI controller * One Fast-mode Plus I²C-bus interface with monitor mode and open-drain I/Opins conforming to the full I²C-bus specification. Supports data rates of up to1 Mbit/s * One standard I²C-bus interface with monitor mode and with standard I/O pins * Two I²S interfaces, each with DMA support and with one input and one output * Digital peripherals: * External Memory Controller EMC supporting external SRAM, ROM, NOR flash,and SDRAM devices * LCD controller with DMA support and a programmable display resolution of up to1024 H x768 V. Supports monochrome and color STN panels and TFT colorpanels; supports 1/2/4/8 bpp Color Look-Up Table CLUT and 16/24-bit direct pixelmapping * Secure Digital Input Output SD/MMC card interface * Eight-channel General-Purpose DMA GPDMA controller can access all memorieson the AHB and all DMA-capable AHB slaves * 164 General-Purpose Input/Output GPIO pins with configurable pull-up/pull-downresistors and open-drain mode