LPC43S37JET100E

LPC43S 系列 1 MB 闪存 49 I/O 32-位 ARM Cortex-M4/M0 MCU - TFBGA-100

Overview

The LPC43S37JET100 is a ARM Cortex-M4 based microcontroller for embedded applications which includes an ARM Cortex-M0 coprocessor, 1 MB of flash and 136 kB of on-chip SRAM, 16 kB of EEPROM memory, security features with AES engine, a quad SPI Flash Interface SPIFI, advanced configurable peripherals such as the State Configurable Timer SCT and the Serial General Purpose I/O SGPIO interface, two High-speed USB controllers, Ethernet, an external memory controller, and multiple digital and analog peripherals. The LPC43S37JET100 operates at CPU frequencies of up to 204 MHz.

The ARM Cortex-M4 is a 32-bit core that offers system enhancements such as low power consumption, enhanced debug features, and a high level of support block integration. The ARM Cortex-M4 CPU incorporates a 3-stage pipeline, uses a Harvard architecture with separate local instruction and data buses as well as a third bus for peripherals, and includes an internal prefetch unit that supports speculative branching. The ARM Cortex-M4 supports single-cycle digital signal processing and SIMD instructions. A hardware floating-point unit is integrated in the core. The ARM Cortex-M4 with floating-point unit is often referred to as M4F.

The ARM Cortex-M0 coprocessor is an energy-efficient and easy-to-use 32-bit core which is upward code- and tool-compatible with the Cortex-M4 core. The Cortex-M0 coprocessor, designed as a replacement for existing 8/16-bit microcontrollers, offers up to 204 MHz performance with a simple instruction set and reduced code size.

MoreLess

## Features

* Cortex-M4 Processor core

* ARM Cortex-M4 processor version r0p1, running at frequencies of up to 204 MHz.

* Built-in Memory Protection Unit MPU supporting eight regions.

* Built-in Nested Vectored Interrupt Controller NVIC.

* Hardware floating-point unit.

* Non-maskable Interrupt NMI input.

* JTAG and Serial Wire Debug SWD, serial trace, eight breakpoints, and four watch points.

* Enhanced Trace Module ETM and Enhanced Trace Buffer ETB support.

* System tick timer.

* Cortex-M0 Processor core

* ARM Cortex-M0 coprocessor version r0p0 capable of off-loading the main ARM Cortex-M4 application processor.

* Running at frequencies of up to 204 MHz.

* JTAG

* Built-in NVIC.

* On-chip memory

* 1 MB on-chip dual bank flash memory with flash accelerator.

* 16 kB on-chip EEPROM data memory.

* 136 kB SRAM for code and data use.

* Multiple SRAM blocks with separate bus access. Two SRAM blocks can be powered down individually.

* 64 kB ROM containing boot code and on-chip software drivers.

* 64 bit of One-Time Programmable OTP memory for general-purpose use.

* Two banks 256 bit total One-Time Programmable OTP memory for AES key storage. One bank can store an encrypted key for decoding the boot image.

* AES engine for encryption and decryption of the boot image and data with DMA support and programmable via a ROM-based API.

* Configurable digital peripherals

* Serial GPIO SGPIO interface.

* State Configurable Timer SCT subsystem on AHB.

* Global Input Multiplexer Array GIMA allows to cross-connect multiple inputs and outputs to event driven peripherals like the timers, SCT, and ADC0/1.

* Serial interfaces

* Quad SPI Flash Interface SPIFI with four lanes and up to 52 MB per second.

* 10/100T Ethernet MAC with RMII and MII interfaces and DMA support for high throughput at low CPU load. Support for IEEE 1588 time stamping/advanced time stamping IEEE 1588-2008 v2.

* One High-speed USB 2.0 Host/Device interface with DMA support, on-chip full-speed PHY and ULPI interface to external high-speed PHY

* USB interface electrical test software included in ROM USB stack.

* One 550 UART with DMA support and full modem interface.

* Three 550 USARTs with DMA and synchronous mode support and a smart card interface conforming to ISO7816 specification. One USART with IrDA interface.

* Up to two C_CAN 2.0B controllers with one channel each.

* Two SSP controllers with FIFO and multi-protocol support. Both SSPs with DMA support.

* One SPI controller.

* One Fast-mode Plus I²C-bus interface with monitor mode and with open-drain I/O pins conforming to the full I²C-bus specification. Supports data rates of up to 1 Mbit/s.

* One standard I²C-bus interface with monitor mode and with standard I/O pins.

* Two I²S interfaces, each with DMA support and with one input and one output.

* Digital peripherals

* External Memory Controller EMC supporting external SRAM, ROM, NOR flash, and SDRAM devices.

* Secure Digital Input Output SD/MMC card interface.

* Eight-channel General-Purpose DMA controller can access all memories on the AHB and all DMA-capable AHB slaves.

* Up to 49 General-Purpose Input/Output GPIO pins with configurable pull-up/pull-down resistors.

* GPIO registers are located on the AHB for fast access. GPIO ports have DMA support.

* Up to eight GPIO pins can be selected from all GPIO pins as edge and level sensitive interrupt sources.

* Two GPIO group interrupt modules enable an interrupt based on a programmable pattern of input states of a group of GPIO pins.

* Four general-purpose timer/counters with capture and match capabilities.

* Repetitive Interrupt timer RI timer.

* Windowed watchdog timer WWDT.

* Ultra-low power Real-Time Clock RTC on separate power domain with 256 bytes of battery powered backup registers.

* Alarm timer; can be battery powered.

* Analog peripherals

* One 10-bit DAC with DMA support and a data conversion rate of 400 kSamples/s.

* Two 10-bit ADCs with DMA support and a data conversion rate of 400 kSamples/s. Up to eight input channels per ADC.

* Unique ID for each device.

* Clock generation unit

* Crystal oscillator with an operating range of 1 MHz to 25 MHz.

* 12 MHz internal RC oscillator trimmed to 3 % accuracy over temperature and voltage 1.5 % accuracy for Tamb = 0 °C to 85 °C.

* Ultra-low power Real-Time Clock RTC crystal oscillator.

* Three PLLs allow CPU operation up to the maximum CPU rate without the need for a high-frequency crystal. The second PLL can be used with the High-speed USB, the third PLL can be used as audio PLL.

* Clock output.

* Power

* Single 3.3 V 2.4 V to 3.6 V power supply with on-chip DC-to-DC converter for the core supply and the RTC power domain.

* RTC power domain can be powered separately by a 3 V battery supply.

* Four reduced power modes: Sleep, Deep-sleep, Power-down, and Deep power-down.

* Processor wake-up from Sleep mode via wake-up interrupts from various peripherals.

* Wake-up from Deep-sleep, Power-down, and Deep power-down modes via external interrupts and interrupts generated by battery powered blocks in the RTC power domain.

* Brownout detect with four separate thresholds for interrupt and forced reset.

* Power-On Reset POR.

* Available as TFBGA100 package.

## Target Applications

* Secure industrial gateways

* Automotive aftermarket, including telematics

* Smart meters

* Industrial controls

* Industrial automation

* Diagnostic equipment

* White goods HMI

* Data collectors and navigation

* Electronic instruments

## Features

* Electronic instruments